slide-2016-videos_phone slide-2016-videos_phone_landscape slide-2016-videos_tablet slide-2016-videos_main

To get notifications about new videos subscribe to our YouTube channel.

TITAN and Dual Sector Gear: 50RPS test

Published 26.09.2016

 


WARFET: How to read and clear DTC?

Published 26.08.2016

 


TITAN drop-in: Innovative fire selector mode SEMI [SAFE] - BURST - AUTO

Published 27.06.2016

 


TITAN drop-in: Trigger Sensitivity Adjustment

Published 08.06.2016

 


TITAN drop-in: Configurable Fire Selector

Published 26.05.2016

 


TITAN drop-in: Hair Trigger Function Presentation

Published 04.05.2016

 


Installation of PicoSSR 3 with replacement of wires (GB V2)

Published 08.04.2016

 


WARFET: Pre-cocking AUTO improvement ver. 1.1 (software update)

Published 06.02.2016

We would like to announce that we have developed the new software version for WARFET. We made improvement in pre-cocking AUTO function. After the update, the piston stops in pre-cocking postion immediately after firing a shot. We eliminated the break between a shot and precocking.


Your AEG with GATE mosfet does not fire? Check if the mosfet properly recognizes signal

Published 14.07.2015

If your AEG is not firing, you can have a problem with signal wires or trigger contacts, not with a MOSFET. You can easily exclude that the problem lies in your MOSFET. The video shows 4 methods how to do this. If your AEG is firing while shorting signal socket, this means the MOSFET works properly.


GATE NanoHARD - Checking short-circuit protection

Published 02.03.2015

 


NanoHARD - Understanding green LED

Published 24.02.2015

BUILT-IN SELF-TEST
The green LED circuit is directly connected to the output transistors.
1. The green LED blinks quickly on and off
--- Active Brake ON
2. The green LED lights up quickly and slowly dies
--- Active Brake OFF
3. The green LED is still off
--- One possibility: Programmed protection for the battery with higher voltage than the one that is currently connected


NanoHARD - How to turn ON/OFF Active Brake

Published 24.02.2015

1. Insert the jumper
2. Connect the battery
3. Wait until the blue LED goes off
4. Pull out the jumper
5. Connect the Programming Button
6. PRESS & HOLD --- confirm the last selected value of the battery protection
7. SHORT PRESS --- move to the next value
8. PRESS & HOLD --- confirm the selected value
You successfully turned off the Active Brake.


NanoHARD - Going through the entire configuration

Published 24.02.2015

1. Insert the jumper
2. Connect the battery
3. Wait until the blue LED goes off
4. Pull out the jumper
5. Connect the Programming Button
6. SHORT PRESS --- move to next value
--- LED blinks once - Battery protection disabled
--- LED blinks two times - 7.4V Li-po protection
--- LED blinks three times - 11.1V Li-po protection
--- LED blinks four times - 14.8V Li-po protection
7. PRESS & HOLD --- confirm the selected value and move to Active Brake programming
8. SHORT PRESS --- move to next value
--- LED blinks once slowly and once quickly - Active Brake OFF
--- LED blinks once slowly and twice quickly - Active Brake ON
9. PRESS & HOLD --- confirm the selected value


NanoHARD - How to program Li-Po battery protection

Published 24.02.2015

1. Insert the jumper
2. Connect the battery
3. Wait until the blue LED goes off
4. Pull out the jumper
5. Connect the Programming Button
6. SHORT PRESS --- move to the next value
7. PRESS & HOLD --- confirm the selected value and move to Active Brake programming
8. PRESS & HOLD --- confirm the last selected value of Active Brake option


GATE MERF 3.2 - Restoring factory settings

Published 17.08.2014

MERF 3.2 factory settings:
Battery: NiCd 7.2V
ROF Control: 100%
Smart trigger: OFF
Burst time approximately: 288ms
Burst time precisely: +0ms
Operating mode: Enchanced mode SEMI/AUTO


GATE MERF 3.2 - gun shoots without pulling the trigger - solving problem

Published 17.08.2014

This short movie shows the solution for a problem when AEG with MERF 3.2 mosfet shoots immediately after connecting a battery.


GATE PicoAAB - Standard kit presentation

Published 31.07.2014

TITAN and Dual Sector Gear: 50RPS test

Published 26.09.2016

Link to video

 


WARFET: How to read and clear DTC?

Published 26.08.2016

Link to video

 


TITAN drop-in: Innovative fire selector mode SEMI [SAFE] - BURST - AUTO

Published 27.06.2016

Link to video

 


TITAN drop-in: Trigger Sensitivity Adjustment

Published 08.06.2016

Link to video

 


TITAN drop-in: Configurable Fire Selector

Published 26.05.2016

Link to video

 


TITAN drop-in: Hair Trigger Function Presentation

Published 04.05.2016

Link to video

 


Installation of PicoSSR 3 with replacement of wires (GB V2)

Published 08.04.2016

Link to video

 


WARFET: Pre-cocking AUTO improvement ver. 1.1 (software update)

Published 06.02.2016

Link to video

We would like to announce that we have developed the new software version for WARFET. We made improvement in pre-cocking AUTO function. After the update, the piston stops in pre-cocking postion immediately after firing a shot. We eliminated the break between a shot and precocking.


Your AEG with GATE mosfet does not fire? Check if the mosfet properly recognizes signal

Published 14.07.2015

Link to video

If your AEG is not firing, you can have a problem with signal wires or trigger contacts, not with a MOSFET. You can easily exclude that the problem lies in your MOSFET. The video shows 4 methods how to do this. If your AEG is firing while shorting signal socket, this means the MOSFET works properly.


GATE NanoHARD - Checking short-circuit protection

Published 02.03.2015

Link to video

 


NanoHARD - Understanding green LED

Published 24.02.2015

Link to video

BUILT-IN SELF-TEST
The green LED circuit is directly connected to the output transistors.
1. The green LED blinks quickly on and off
--- Active Brake ON
2. The green LED lights up quickly and slowly dies
--- Active Brake OFF
3. The green LED is still off
--- One possibility: Programmed protection for the battery with higher voltage than the one that is currently connected


NanoHARD - How to turn ON/OFF Active Brake

Published 24.02.2015

Link to video

1. Insert the jumper
2. Connect the battery
3. Wait until the blue LED goes off
4. Pull out the jumper
5. Connect the Programming Button
6. PRESS & HOLD --- confirm the last selected value of the battery protection
7. SHORT PRESS --- move to the next value
8. PRESS & HOLD --- confirm the selected value
You successfully turned off the Active Brake.


NanoHARD - Going through the entire configuration

Published 24.02.2015

Link to video

1. Insert the jumper
2. Connect the battery
3. Wait until the blue LED goes off
4. Pull out the jumper
5. Connect the Programming Button
6. SHORT PRESS --- move to next value
--- LED blinks once - Battery protection disabled
--- LED blinks two times - 7.4V Li-po protection
--- LED blinks three times - 11.1V Li-po protection
--- LED blinks four times - 14.8V Li-po protection
7. PRESS & HOLD --- confirm the selected value and move to Active Brake programming
8. SHORT PRESS --- move to next value
--- LED blinks once slowly and once quickly - Active Brake OFF
--- LED blinks once slowly and twice quickly - Active Brake ON
9. PRESS & HOLD --- confirm the selected value


NanoHARD - How to program Li-Po battery protection

Published 24.02.2015

Link to video

1. Insert the jumper
2. Connect the battery
3. Wait until the blue LED goes off
4. Pull out the jumper
5. Connect the Programming Button
6. SHORT PRESS --- move to the next value
7. PRESS & HOLD --- confirm the selected value and move to Active Brake programming
8. PRESS & HOLD --- confirm the last selected value of Active Brake option


GATE MERF 3.2 - Restoring factory settings

Published 17.08.2014

Link to video

MERF 3.2 factory settings:
Battery: NiCd 7.2V
ROF Control: 100%
Smart trigger: OFF
Burst time approximately: 288ms
Burst time precisely: +0ms
Operating mode: Enchanced mode SEMI/AUTO


GATE MERF 3.2 - gun shoots without pulling the trigger - solving problem

Published 17.08.2014

Link to video

This short movie shows the solution for a problem when AEG with MERF 3.2 mosfet shoots immediately after connecting a battery.


GATE PicoAAB - Standard kit presentation

Published 31.07.2014

Link to video